The General Plan

Build

FAA Issues Three Aviation Safety NPRMs; HUD Seeks Labor Standards Paperwork Revision

The FAA has opened comment periods on proposed airworthiness directives covering P&WC turbofan engines, Boeing 747 hydraulic pumps, and Boeing 787 wing fasteners, while HUD seeks OMB approval for a revised federal labor standards complaint collection.

P&WC Engine Life-Limited Parts (Docket FAA-2026-13811)

The FAA proposes a new airworthiness directive (AD) for all Pratt & Whitney Canada Corp. Model PW814GA and PW815GA engines. According to the NPRM, the action was prompted by P&WC revising the airworthiness limitations section (ALS) of its existing airworthiness limitations manual (ALM) to introduce new or more restrictive airworthiness limitations and associated thresholds and intervals for life-limited parts. The proposed AD would require operators to update the ALS of their existing ALM or instructions for continued airworthiness (ICA), and their existing approved maintenance or inspection program, to incorporate those new or more restrictive instructions.

The document explains that Transport Canada first issued AD CF-2023-73, dated November 3, 2023, requiring replacement or inspection of affected components prior to reaching their updated limits. After the manufacturer subsequently revised the ALS to introduce further restrictions, Transport Canada superseded that earlier AD and issued AD CF-2025-71, dated December 30, 2025, which is the mandatory compliance document the FAA's proposed rule would incorporate by reference. The document states that this condition, if not addressed, could result in damage to the engine and damage to the airplane. The FAA notes the products are approved for operation in the United States under a bilateral agreement with Transport Canada and that the unsafe condition is likely to exist or develop on other products of the same type design. Comments are due by December 28, 2026.

Boeing 747-400 ACMP Fire Risk (Docket FAA-2026-13810)

The FAA proposes a new AD for all Boeing Model 747-400 and 747-400F series airplanes, prompted by a report of an overheated alternating current motor pump (ACMP) that caused a fire in the main landing gear (MLG) wheel well. The document explains that an investigation traced the cause to a missing lock washer and nut from a moving contact in the related electrical load control unit (ELCU), which left the main contact operator bar unrestrained and allowed two-phase power to reach the ACMP, causing it to overheat, leak hydraulic fluid, and start the fire. The document states this condition, if not addressed, could result in the ACMP overheating and igniting a fire in the wheel well, with consequent damage to the airplane, loss of continued safe flight and landing, and/or personnel injury.

The proposed AD would require a maintenance records check or inspection for any installed ACMP with part number (P/N) 731966 and applicable on-condition actions, and would prohibit the installation of affected parts. On-condition actions include replacing each affected ACMP with an ACMP having P/N 3033115-100. The document notes that a parallel AD, AD 2026-19-04, Amendment 39-23471 (91 FR 61127, September 28, 2026), already addresses the same unsafe condition on Boeing Model 777-200, -200LR, -300, -300ER, and -777F series airplanes. The referenced compliance material is Boeing Alert Requirements Bulletin 747-29A2132 RB, dated March 5, 2026. Comments are due by December 28, 2026.

Boeing 787-8 Wing Fastener Lightning Protection (Docket FAA-2026-13802)

The FAA proposes a new AD for certain Boeing Model 787-8 airplanes, prompted by a report that wing skin outer mold line (OML) penetrating fasteners installed using threaded nuts without cap seals do not provide reliable protection against potential ignition sources when subjected to direct attachment lightning currents. The document states this condition, if not addressed, could lead to a potential ignition source inside the wing fuel tanks, surge tanks, or dry bays during a lightning strike event, which could result in a consequent fire or explosion.

The proposed AD would require: inspecting between rib 25 and rib 31 on the left and right wing for wing skin penetrating fasteners with a threaded nut adjacent to the electromagnetic effects (EME) sleeve; inspecting the left and right wing fuel tanks, surge tanks, and dry bays for threaded nuts installed on fasteners that penetrate the upper and lower wing skins; accomplishing the inspection specified in airworthiness limitation AWL No. 57-AWL-18; and revising the maintenance program to incorporate that airworthiness limitation task. On-condition actions include replacing affected EME sleeves with new ones at all affected locations and installing a cap seal on all wing skin penetrating fasteners found with a threaded nut. The referenced compliance material is Boeing Alert Requirements Bulletin B787-81205-SB570039-00 RB, Issue 001, dated June 8, 2026. Comments are due by December 28, 2026.

Laughlin AFB Class C Airspace Administrative Correction

Separately, the FAA has finalized administrative amendments to the Laughlin AFB, TX, Class C airspace legal description under 14 CFR part 71. The rule updates the geographic coordinates of the airport reference point (ARP) from lat. 29°21'36" N, long. 100°46'39" W to lat. 29°21'34" N, long. 100°46'41" W — a 2-second difference in latitude and longitude — to match the FAA's National Airspace System Resources (NASR) database. The rule also updates the text header from "ASW TX C Laughlin AFB, TX" to "ASW TX C Del Rio, TX" and replaces the outdated term "Airport/Facility Directory" with "Chart Supplement." The document states the action does not change the lateral boundaries, altitudes, or operating requirements of the Class C airspace area. The FAA determined good cause existed to bypass notice and comment, characterizing the action as routine and de minimis in impact. The rule is effective 0901 UTC, February 18, 2027.

HUD Federal Labor Standards Information Collection Revision

The Department of Housing and Urban Development is seeking OMB approval to revise a currently approved information collection under OMB Approval Number 2501-0018, covering four forms: HUD-4730, HUD-4731, HUD-4010, and HUD-4720. The document states that the information is used by HUD to fulfill its obligation to enforce federal labor standards provisions, particularly to act upon allegations of labor standards violations. The HUD-4730 questionnaires are primarily used to determine whether payroll information supplied by employers is valid; the HUD-4731 Complaint Intake Form collects information from complainants alleging violations of federal labor standards on HUD-assisted projects; the HUD-4720 is an optional tool for contractors to develop a reference document for wage rates; and the HUD-4010 is a read-only form establishing federal labor standards requirements contractors and subcontractors must follow in contracts and bid solicitations.

The notice estimates 8,950 respondents and 8,950 total annual responses, with an average of 0.5 hours per response and total estimated burden of 4,450 hours. The estimated hourly cost of $42.50 is based on Bureau of Labor Statistics May 2026 National Occupational Employment and Wages Estimates for Compliance Officers (SOC 13-1041). The public comment period closes January 12, 2027.

What to watch

  • December 28, 2026: Comment deadline for all three FAA airworthiness directive NPRMs — P&WC PW814GA/PW815GA engines (Docket FAA-2026-13811), Boeing 747-400/747-400F ACMP (Docket FAA-2026-13810), and Boeing 787-8 wing fasteners (Docket FAA-2026-13802).
  • January 12, 2027: HUD comment deadline for the federal labor standards information collection revision (OMB No. 2501-0018).
  • February 18, 2027: Effective date of the Laughlin AFB, TX, Class C airspace administrative amendment.

What this means for recipients

For state, local, and tribal governments or consultants working with HUD-assisted construction programs, the proposed revision to OMB No. 2501-0018 directly affects the forms used to investigate and document federal labor standards compliance — including the HUD-4731 complaint intake process — and the 60-day comment window ending January 12, 2027 is the opportunity to influence burden estimates or form design. Aviation operators and maintenance organizations responsible for P&WC PW814GA/PW815GA engines, Boeing 747-400/747-400F aircraft, or Boeing 787-8 aircraft should review the respective NPRMs and assess whether compliance with proposed inspection, maintenance program revision, and parts-replacement requirements would affect their maintenance schedules and approved programs. The Laughlin AFB Class C airspace rule requires no operational changes from affected airspace users, as the document confirms boundaries, altitudes, and operating requirements are unchanged.

Related

Sources

37 cited

Every hard fact above is grounded in and cited to a primary source record.

  1. The P&WC NPRM was prompted by the manufacturer revising the airworthiness limitations section of the existing airworthiness limitations manual to introduce new or more restrictive airworthiness limitations and associated thresholds and intervals for life-limited parts.

    federalregister.gov
  2. The proposed AD would require updating the ALS of the existing ALM or ICA and the existing approved maintenance or inspection program to incorporate new or more restrictive instructions and associated thresholds and intervals for life-limited parts.

    federalregister.gov
  3. Transport Canada issued AD CF-2023-73, dated November 3, 2023, requiring replacement or inspection of affected components prior to reaching their updated limits.

    federalregister.gov
  4. Transport Canada superseded AD CF-2023-73 and issued AD CF-2025-71, dated December 30, 2025.

    federalregister.gov
  5. Comments on the P&WC engine NPRM are due by December 28, 2026.

    federalregister.gov
  6. The FAA proposes a new AD for all Boeing Model 747-400 and 747-400F series airplanes.

    federalregister.gov
  7. The 747 NPRM was prompted by a report of an overheated ACMP that caused a fire in the main landing gear wheel well.

    federalregister.gov
  8. The 747 condition, if not addressed, could result in the ACMP overheating and igniting a fire in the wheel well and consequent damage to the airplane, loss of continued safe flight and landing, and/or personnel injury.

    federalregister.gov
  9. The proposed 747 AD would require a maintenance records check or inspection for any installed ACMP with part number 731966 and applicable on-condition actions, and would prohibit the installation of affected parts.

    federalregister.gov
  10. On-condition actions for the 747 include replacing each affected ACMP with an ACMP having P/N 3033115-100.

    federalregister.gov
  11. AD 2026-19-04, Amendment 39-23471 (91 FR 61127, September 28, 2026), addresses the same unsafe condition on Boeing Model 777-200, -200LR, -300, -300ER, and -777F series airplanes.

    federalregister.gov
  12. The referenced compliance material for the 747 AD is Boeing Alert Requirements Bulletin 747-29A2132 RB, dated March 5, 2026.

    federalregister.gov
  13. Comments on the Boeing 747 ACMP NPRM are due by December 28, 2026.

    federalregister.gov
  14. The FAA proposes a new AD for certain Boeing Model 787-8 airplanes.

    federalregister.gov
  15. The 787 NPRM was prompted by a report that wing skin OML penetrating fasteners installed using threaded nuts without cap seals do not provide reliable protection against potential ignition sources when subjected to direct attachment lightning currents.

    federalregister.gov
  16. The 787 condition, if not addressed, could lead to a potential ignition source inside the wing fuel tanks, surge tanks, or dry bays during a lightning strike event, which could result in a consequent fire or explosion.

    federalregister.gov
  17. The proposed 787 AD would require inspecting between rib 25 and rib 31 on the left and right wing for wing skin penetrating fasteners with a threaded nut adjacent to the EME sleeve.

    federalregister.gov
  18. The proposed 787 AD would require inspecting the left and right wing fuel tanks, surge tanks, and dry bays for threaded nuts installed on fasteners that penetrate the upper and lower wing skins.

    federalregister.gov
  19. The proposed 787 AD would require accomplishing the inspection specified in AWL No. 57-AWL-18 and revising the maintenance program to incorporate that airworthiness limitation task.

    federalregister.gov
  20. On-condition actions for the 787 include replacing affected EME sleeves with new ones at all affected locations and installing a cap seal on all wing skin penetrating fasteners found with a threaded nut.

    federalregister.gov
  21. The referenced compliance material for the 787 AD is Boeing Alert Requirements Bulletin B787-81205-SB570039-00 RB, Issue 001, dated June 8, 2026.

    federalregister.gov
  22. Comments on the Boeing 787-8 wing fastener NPRM are due by December 28, 2026.

    federalregister.gov
  23. The Laughlin AFB, TX, Class C airspace rule updates the geographic coordinates of the ARP from lat. 29°21'36" N, long. 100°46'39" W to lat. 29°21'34" N, long. 100°46'41" W, a 2-second difference in latitude and longitude, to match the FAA's NASR database.

    federalregister.gov
  24. The Laughlin AFB rule does not change the lateral boundaries, altitudes, or operating requirements of the Class C airspace area.

    federalregister.gov
  25. The Laughlin AFB Class C airspace rule is effective 0901 UTC, February 18, 2027.

    federalregister.gov
  26. HUD is seeking OMB approval to revise information collection OMB Approval Number 2501-0018, covering forms HUD-4730, HUD-4731, HUD-4010, and HUD-4720.

    federalregister.gov
  27. The HUD-4730 questionnaires are primarily used to determine whether payroll information supplied by employers is valid.

    federalregister.gov
  28. The HUD-4731 Complaint Intake Form is used to collect information from complainants alleging violations of federal labor standards on HUD-assisted projects.

    federalregister.gov
  29. The HUD-4720 is an optional tool for contractors to develop a reference document for wage rates.

    federalregister.gov
  30. The HUD-4010 is a read-only form that establishes the federal labor standards requirements contractors and subcontractors must follow in contracts and bid solicitations.

    federalregister.gov
  31. The HUD information collection notice estimates 8,950 respondents and 8,950 total annual responses, with an average of 0.5 hours per response and total estimated burden of 4,450 hours.

    federalregister.gov
  32. The estimated hourly cost of $42.50 is based on Bureau of Labor Statistics May 2026 National Occupational Employment and Wages Estimates for Compliance Officers (SOC 13-1041).

    federalregister.gov
  33. The HUD comment period closes January 12, 2027.

    federalregister.gov
  34. The Laughlin AFB rule updates the text header from 'ASW TX C Laughlin AFB, TX' to 'ASW TX C Del Rio, TX' and replaces the outdated term 'Airport/Facility Directory' with 'Chart Supplement.'

    federalregister.gov
  35. The FAA proposes a new AD for all Pratt & Whitney Canada Corp. Model PW814GA and PW815GA engines.

    federalregister.gov
  36. The P&WC condition, if not addressed, could result in damage to the engine and damage to the airplane.

    federalregister.gov
  37. Investigation found that a lock washer and nut was missing from a moving contact in the related electrical load control unit, leaving the main contact operator bar unrestrained and allowing two-phase power to reach the ACMP, causing it to overheat, leak hydraulic fluid, and start a fire in the MLG wheel well.

    federalregister.gov